Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: Ford Australias High Riding Utes

  1. #1
    Aka Captain Slow TS50's Avatar
    Join Date
    Jan 2012
    Location
    Launceston Tasmania
    Posts
    7,144

    Ford Australias High Riding Utes

    http://www.msn.com/en-au/motoring/ne...C&ocid=ue01dhp

    Its worth going to the above article to see the 4 door Falcon ute


    Australia’s best concepts: Ford’s high-riding utes

    Wheels Magazine

    Daniel Gardner


    In a previous look back at Australia’s best concepts, we used Toyota’s X-Runner as an example of a vehicle that previewed the future of go-anywhere utes, but they weren’t the only brand to see the potential. Ford also experimented with the idea not once, but twice, with two design studies.

    The blue oval first dabbled in the idea with a concept based on the XH Falcon Ute that was developed in partnership with RMIT design students, and made its debut at the Melbourne motor show in 1997.

    Using a standard 4.0-litre six-cylinder ute as a blank canvas, the Terra had its suspension raised by 40mm and was given a set of 15-inch alloy wheels dressed in massive Yokohama mud tyres.

    It might have had the looks, ground clearance, and rubber for some serious off-road action but, like the Ute on which it was based, the Terra was rear-drive only, which limited just how far into the bush Ford’s all-terrain tradie would actually be able to go.

    Up front was a chrome-plated nudge bar with incorporated underbody bash plate for ungainly wildlife and ill-placed rocks, while the skeleton tailgate mimicked the construction with more bar work.

    Overhead, a sports bar, also in chrome, supported massive driving lamps that look decidedly dated in today’s world of slim LED light bars, but on the inside, its sat-nav was front-line tech.

    While it is hard to equate the value of any concept that doesn’t make it into production, it’s safe to say the XH Terra was a bit of fun and little more than an opportunity for some good publicity, but for its go-anywhere ute revisit, Ford got a little more serious.

    Debuting at the 2000 Sydney motor show, the Ford R5 again used the underpinnings of the Falcon as its basis (this time the AU XR8 sedan - not the ute) but added more significant changes, including a completely new body from the B-pillar back to accommodate a second row of seating as well as a tray.


    A dual-cab ute with off-road promise – sound familiar? For its second ute concept, Ford was even closer to the recipe that would go on to make the Ranger such a hit with Australian customers.

    Like the XH Terra, the R5 was also rear-drive with a raised ride height and knobbly tyres, but boosted its all-terrain ability with an electronic traction control system that was tailored for loose surfaces rather than asphalt. It also had its 5.0 litres of V8 power sent through a manual gearbox for maximum grunt.

    At the time of its launch, Ford Australia’s chief designer Rob Strong said the tough truck was far more than a show pony, and wasn’t far from production, if given the green light.

    “It’s not out there to just titillate show-goers,” he said. “It’s a credible idea.”

    Race car side-exit exhausts would never have made it from show floor to show room, but there were other features that showed real promise, including the 240-volt charge socket built into the rear bumper, as was a 50-litre water tank and an electric winch at the front – items that are prized by hardcore off-road enthusiasts today.

    Access to the second row of seating was made easier via a suicide-opening rear door on the driver’s side; instead of having to scramble past the front row. If the load tray capacity of the two-seater AU ute was needed, a clever 60/40 folding hatch allowed items to be loaded into the cab from the back.

    The concept’s development cost of $250,000 was minimised, in part, by poaching components from other models such as the air vents from a Ka, a steering wheel sourced from the Mondeo, and tailgate hinges from an F150 truck.

    There were glimpses of future design however, including the faired-in quad headlights that would feature later in the Falcon’s lifecycle.

    But more importantly, both the Terra and R5 were prophetically close to the blue oval we know today with the Ranger sitting at the top of Ford’s sales pile and as Australia’s second favourite car overall, while the Falcon, which offered the basis for both concepts, has been put out to pasture.
    2002 T3 Manual Naroma Blue TS-50 (049)Sunroof, Premium Sound, Black/Blue Leather, Brembos

  2. The Following User Says Thank You to TS50 For This Useful Post:

    FTe217 (11th August 2017)

  3. #2
    T3/Sprint8 FTe217's Avatar
    Join Date
    Jan 2012
    Location
    Richmond
    Posts
    9,881
    Could have should have.
    The XY's from memory had a raised version as well if I recall right ????
    Look, think Crewman, (that tbh I didn't mind the look but the back seats were far worse than jap dual cabs) it just didn't take enough did it and they at the time having far better market share.
    Funny, our market just didn't take to the local offerings in utes raised or even wagons such as the Aventra as well yet went out and bought countless Jap/Korean SUV's.
    I feel the general market just got sick of locals and the bogan type halo but for us devotees.
    YNWA ! off to CL 2018.
    Sydney is Sky Blue HAL Premiers/Champions 2017 - the Double.

  4. #3
    Miami Sprint. 4Vman's Avatar
    Join Date
    Jan 2012
    Location
    Melbourne
    Posts
    18,793
    The XY's were an aftermarket 4WD kit fitted by Dealers.
    My Falcon family heritage: XY V8 Falcon 500, XYGT, XBGT, XC 351 GS, XD 4.1 Spack, EF wagon, AU Wagon, AU2 Wagon, AU2 XR8, BA XR8, BF XR8, FG XR6, Lucky last: Sprint 8. Oh wait, AU3 XLS Marlin Ute!

  5. #4
    T3/Sprint8 FTe217's Avatar
    Join Date
    Jan 2012
    Location
    Richmond
    Posts
    9,881
    yer thats it thanks.
    YNWA ! off to CL 2018.
    Sydney is Sky Blue HAL Premiers/Champions 2017 - the Double.

  6. #5
    Validated User Road_Warrior's Avatar
    Join Date
    Mar 2012
    Location
    In the cockpit. Cruisin' mah hood
    Posts
    5,281
    The XY 4x4 utes were converted by a subcontractor for Ford Australia in Brisbane and you will find they are all JH utes. The axles were Dana and transfer case was a Jeep unit.
    "You might not notice them, but those few standing proud are the reason some can stand at all."

  7. The Following 3 Users Say Thank You to Road_Warrior For This Useful Post:

    4Vman (11th August 2017),FTe217 (11th August 2017),Randel (12th August 2017)

  8. #6
    Aka Captain Slow TS50's Avatar
    Join Date
    Jan 2012
    Location
    Launceston Tasmania
    Posts
    7,144
    I actually thought Haywards down here in Tasmania did the xy's?
    2002 T3 Manual Naroma Blue TS-50 (049)Sunroof, Premium Sound, Black/Blue Leather, Brembos

  9. #7
    T3/Sprint8 FTe217's Avatar
    Join Date
    Jan 2012
    Location
    Richmond
    Posts
    9,881
    I recall something re Tas.
    YNWA ! off to CL 2018.
    Sydney is Sky Blue HAL Premiers/Champions 2017 - the Double.

  10. #8
    Aka Captain Slow TS50's Avatar
    Join Date
    Jan 2012
    Location
    Launceston Tasmania
    Posts
    7,144
    4WD XY.jpg
    Appologies, was definitely Brisbane, Haywards must have been doing their own aftermarket version

    http://www.truckjungle.com/2012/08/1...alcon-4x4-ute/


    Aussie Classic: Ford XY Falcon 44 Ute
    Published on August 18, 2012 | By Mark Oastler |

    The catalyst for the short-lived Ford XY Falcon 44 ute was the Australian Army, according to the late Howard Marsden, who was head of Ford Special Vehicles at the time.
    In an interview conducted in 2001, Marsden said that the four cylinder-powered Land Rovers being used by the Army at the time were proving to be too underpowered, given that they often had to lug heavy payloads of troops and equipment and cover huge distances.
    So in the late 1960s, the Army put out a tender to local manufacturers for expressions of interest in building a new 44 light truck with a more powerful six cylinder engine that could out-perform their Land Rovers.
    Given the potential for large volume government fleet sales for the successful tenderer, Ford decided it was a challenge worthy of tackling.
    They certainly had the facilities and specialised knowledge to have a decent shot at it. Ford’s assembly plant in Brisbane already handled the finicky local assembly of imported 2WD F series trucks that required a fair degree of improvisation on the production line.
    And for several years the Brisbane plant had been collaborating with Willys Motors (the local importer of Jeeps) in supplying complete engines and numerous other Falcon parts like clutches and pedal assemblies required for local assembly of CJ5/CJ6 Jeeps.
    These resources, combined with the product planning expertise of Ford Special Vehicles, made Ford* well placed to tackle such a program. In fact Al Turner, Marsden’s predecessor, had already played a key role in development of Ford’s Fiera light truck for the burgeoning Asian market.

    Given Ford’s existing ties with Willys Motors, it was decided that the easiest and most cost-effective answer to the Army light truck tender was to convert the existing six cylinder XY Falcon ute into a 44 version, using proven Jeep drivetrain hardware and transmission adapters etc that already existed for the CJ5/CJ6.
    The greatest engineering challenge Ford faced was to install a complete leaf-sprung live axle assembly under the front of a Falcon ute that was never designed for such things.
    Marsden recalled with some dismay how difficult this task proved to be, as the Falcon ute featured the same unibody construction (body and chassis combined as one unit) as its sedan sibling rather than the traditional and much stronger body-on-ladder-frame design employed by Land Rover and other 44 manufacturers.
    As a result, new mounting points for the front leaf springs fabricated from steel plate had to be welded directly to the bodyshell’s underfloor. High-lift leaf springs and shocks raised the rear end of the utility to match the newly raised front end.
    Another challenge was providing enough clearance between the front axle and the engine’s sump and exhaust system to allow for adequate suspension travel. The simple solution was to make new engine mounts that slanted the engine over to the right by several degrees.
    This tilt was large enough to provide adequate sump-to-axle clearance, but it also required a wedge-shaped spacer to be fitted between the carburettor base and inlet manifold to compensate for this angle change and maintain the correct static float bowl levels.

    Don’t worry how it looks, just make it work. The in-line six had to be slanted to the right to allow clearance between the sump and front diff. Note the extra bracing that tied the firewall to the shock absorber towers for extra chassis strength.
    The Falcon’s 250 cid (4.1 litre) inline six had plenty of performance on tap, with 155 bhp (116kW) @ 4000 rpm and maximum torque of 240 ft/lbs (325Nm) available from a very low 1600 rpm.
    A heavy duty 10-inch dry plate clutch, Borg Warner AS5 T15A three-speed full-synchro gearbox with floor-mounted Jeep gearshift and a Spicer Model 20 two-speed transfer case also with floor lever control got power to the front and rear wheels through one-piece propeller shafts.
    Brakes were 11 x 2-inch drum brakes all round (typical fare for 4x4s of this era) with 16 x 4.5 inch steel rims on skinny 6.00 x 16 all-terrain tyres.
    Ford also developed some useful accessories including a powerful 8000 lb PTO winch (shaft-driven from the transfer case), a heavy duty tow bar and military-style high canvas canopy to cover the load area.
    With a kerb weight of only 3620 lbs (1642 kgs), a useful payload of 1380 lbs (625 kgs), excellent approach and departure angles and a lateral tilt angle up to 45 degrees, the Falcon 44 ute had impressive cross-country performance and a high torque-to-weight ratio with or without load due to its relatively light unibody construction.
    Not that any of this mattered to the Army, because the military never got to the stage of even field-testing Ford’s prototype, Marsden revealed.
    He recalled that during the vehicle’s development, the Army made it clear to Ford that even though the basic concept was right, it was never going to meet their extreme battlefield requirements without the proven strength and durability of a traditional body-on-frame construction.
    Clearly this was a path Ford did not have the resources to follow, which was probably just as well because after seeing what else was (or wasn’t) available, the Army opted for Land Rover’s more powerful six cylinder version.

    When one door closes…
    Fortunately Ford’s work on the local Army truck tender didn’t go to waste, as public interest in the 44 ute was enormous after ‘spy’ photos of it being tested at the company’s vast vehicle proving ground at You Yangs in Victoria appeared in local motoring magazines.
    Marsden said that it was purely public demand that swayed the company bean-counters to approve the XY Falcon 44 ute for series production, which he said also created an instant new market segment for Ford.
    To understand the public clamouring for this ‘cross-over’ type of vehicle, one has to realise that Australia’s national road network in the early 1970s featured a lot more dirt roads than today and the noisy, rough-riding 44 vehicles of the era were nothing like the luxurious leather-lined SUVs we now take for granted.
    So with the need to haul loads across vast poor quality roads in comfort, the appeal of this new hybrid vehicle that combined a half-tonne plus carrying capacity and four wheel drive with many of the creature comforts of a modern sedan, was understandable.
    But there were serious structural problems which had to be solved first, because the standard Falcon ute body was not designed to cope with the high suspension load paths it was being subjected to as a 44 vehicle.
    According to Marsden, body stress fractures resulting from rigorous off-road testing prior to production showed that the front end would need to be beefed up to cope with the pounding dished out by the heavy live axle crashing around beneath it.

    Note metal frames stretching forward from the firewall on each side to boost front chassis rail strength. These frames also restricted steering lock, resulting in this vehicle’s notoriously large turning circle! Note also the spring hangers made from steel plate and axle clearance for the sump and exhaust created by slanting the engine to the right. Narrow shaft with uni-joint is the driveshaft from the transfer case for the Power Take Off (PTO) winch.
    Ford came up with some effective – if fairly crude – engineering solutions. Light steel frames (hidden beneath the front mudguards) spanned from the firewall forward to the radiator support panel on each side to add much needed strength and rigidity to the chassis rails.
    Another brace, fabricated from several peices of u-section steel plate welded together, tied each front spring tower rigidly to the firewall.
    The pre-production testing also showed that the bodyshell wasn’t the only thing that needed beefing up, as the original Dana front axle chosen for the project also proved it was not up to the task.
    A heavier Dana unit with stronger 3300 lb axle capacity was specified for the production model. The standard Falcon ute’s Borg Warner rear axle was retained, as its 2000 lb axle load rating was adequate for the task.

    By this stage of the 44 ute’s development in mid-1971, the XY Falcon range (launched in October 1970) was approaching the end of its production run, with the all-new XA model due for release in March 1972.
    Ford set aside a batch of 432 XY Falcon ute bodies (the reason for this unusual build number is not known) that were earmarked for the 44 production run in the second half of 1971.
    According to Ford workers, those XY ute shells actually remained stockpiled in the backyard of the Brisbane plant for almost a year, as ordering and delivery of the new Dana front axles from the US caused crippling delays.
    By the time the imported front axle units finally arrived, the new XA Falcon range had been on sale for months, which would present a real challenge to dealers trying to sell a superseded XY Falcon ute as a ‘new’ offering alongside the latest swoopy XA model (below).

    However, given the amount of time and money the project had already consumed, it was decided to push ahead as Ford figured typical Falcon 44 ute buyers would be pragmatic mostly rural types that wanted them more for practical reasons than appearances.
    Marsden recalled that each of the 432 XY 44 utes produced at the Brisbane plant were essentially hand-built. They also had to be assembled on weekends by a dedicated team of workers, as each vehicle required the fitting of unique parts that would have disrupted the flow of normal plant production lines during the working week.
    And given the unplanned model overlap, they also scored some XA parts during their construction including the high back bench seat with integral head rests, column-mounted ignition key/steering column lock and screen-bonded rear view mirror.
    When the 432 XY Falcon 44 utes finally went on sale in early 1973 (some say late 1972) for a base price of $3680 with full 12,000 mile/12 month factory warranty, there was considerable pent-up buyer demand and Ford sold every one of them. It was the best get-out-of-jail card FoMoCo could have played.

    Why 432 buyers liked it
    The XY Falcon 44 ute was head and shoulders ahead in performance, comfort and features when compared with the agricultural Land Rover, Land Cruiser and Nissan Patrol offerings at the time.
    For here was a rugged all-terrain light truck that not only offered a load area that was superior to its 4WD cab-chassis competitors, but its standard equipment list included a tonneau cover, sump guard, dual exterior rear view mirrors and a tinted laminated windscreen for starters.
    Occupants enjoyed lots of sedan car features inside, too, which were unheard of in rival 44 trucks.
    These included door-pull arm rests, padded dual swivelling sun visors, swivelling quarter-vent windows, padded dash panel, full ‘airflow’ cabin ventilation, collapsible steering column, ignition and steering column lock, two-speed heater/demister, two-speed electric windscreen wipers and washers and tasteful saddle trim upholstery.
    Factory options included a winch, tow bar and high military-style canopy.
    You could even request a dealer-installed Falcon GT front spoiler and several vehicles (including the one featured in the sales brochure) had one fitted.
    Not that it did anything remotely aerodynamic at that height –it just looked good.
    The front axle was also fitted with a pair of Warn ‘Power Lock’ free-wheeling hubs which were just starting to appear in the aftermarket.
    With the turn of two small keyways on the face of each hub (you had to have a screwdriver or small coin handy) these hubs disengaged the wheels from the front drive axles.
    This handy feature saved fuel and lots of unnecessary wear and tear on the drivetrain when four wheel drive was not required. And in this vehicle’s case, that would have been most of the time.
    *
    Why Ford killed it
    Despite widespread demand from the public and motoring press to continue the 44 ute program with the XA model and beyond, Ford called it quits.
    Numerous theories have abounded over the past four decades as to why, including claims that the 44 design could not meet tough new ADR crash safety standards, or that the new XA body design with its long door openings was not rigid enough.
    According to Marsden, though, the decision not to continue was determined by the same accountants that had approved the XY production run. It was simply that Ford lost so much money on the Falcon 44 ute program that to start all over again with the XA just did not stack up as a sensible business case.
    However, what the XY program did do was alert Ford to growing local demand for the more luxurious breed of 44 light truck that was doing big business in the US, as part a boom in what the Yanks were calling ‘recreational vehicles’ or ‘RVs’ for short.
    The answer was to start imports of the 44 version of Ford’s popular F-series truck from the US, at a much higher price premium, to satisfy that market need. Which it did brilliantly of course. And, through private import companies, continues to this day. And we can thank the XY Falcon 44 ute for playing a part in that. TJ
    2002 T3 Manual Naroma Blue TS-50 (049)Sunroof, Premium Sound, Black/Blue Leather, Brembos

  11. #9
    Senior Member andrewforbes's Avatar
    Join Date
    May 2013
    Posts
    818
    Page doesn't exist

  12. #10
    Validated User Randel's Avatar
    Join Date
    Jan 2012
    Location
    Leeming, Perth
    Posts
    891
    We had an xy 4x4 in for tyres years ago... had a turning circle worse than a mack truck..... horrid...

Page 1 of 2 12 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •